Bondloc B577 Pipe Seal is a high viscosity thixotropic gel paste which cures rapidly, sealing instantly to 10 bar through its Anaerobic cure system in contact with metals in the absence of air (oxygen). When fully cured it resists pressure up to 350 bar. B577 is not suitable for oxygen systems. Good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol, Acetone and Brake Fluid. Typical applications are in sealing of all types of threaded connections against water, oil, gases and most common materials conveyed by pipes. Specification: Resin: Dimethacrylate.Colour: Yellow.Cure Speed with Activator: <10 minutes.Cure Speed without Activator: <15 mins @ 20C.Viscosity: >50,000 cps.Gap Fill: 0.05mm to 0.4mm.Flash Point: >100C.Shelf Life: 12 months @ 20C.Specific Gravity: 1.09.Max. Operating Temperature:150C. Cured Performance: Full Cure Time: 6-12 hours.Typical Breakaway Strength: >6 to <15 N/mm (2).Prevailing Torque: >3 to < 9 N/mm (2).Static Shear Strength: >5 to <15 N/mm (2). Size: 50ml.

Bondloc B480 is a black rubber toughened Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Black Opaque LiquidSpecific Gravity: 25C 1.06 g/cmShelf life: 6 months unopenedViscosity @ 25C: 350 - 450 mPasSize: 20g

Bondloc B454 is a Thixotropic Non-Drip Gel Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25C 1.1 g/cmShelf life: 12 months unopenedViscosity @ 25C: GelSize: 20g

Bondloc B415 is a high viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25C 1.06 g/cmShelf life: 12 months unopenedViscosity @ 25C: 1200 - 1800 Size: 20g

Bondloc B406 is a very Low Viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25C 1.06 g/cmShelf life: 12 months unopenedViscosity @ 25C: 25 - 35 mPas Size: 20g

Bondloc B401 is a Medium Viscosity Cyanoacrylate. It bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25C 1.06 g/cmShelf life: 12 months unopenedViscosity @ 25C: 90 - 120 Size: 20g

The Unibond 781746 holds up to 50Kg per roll and is suitable for both interior and exterior use. It is ideal for mounting hooks, signs, numbers, pictures, cable trunking, bathroom and car accessories. The tape can be used for bonding wood, ceramic tiles, metal, brick, stone, plaster and most plastics. Size: 19 mm x 1.5m.

The Unibond 781742 No More Nails Roll holds up to 20Kg per roll and is suitable for interior use only. It is ideal for mounting hooks, signs, numbers, pictures, cable trunking, bathroom accessories and car accessories. The tape can be used to bond wood, ceramic tiles, metal, brick, stone, plaster and most plastics. Size: 19 mm x 1.5m.

The Unibond 781740 holds up to 2.75Kg per strip and is suitable for both interior and exterior use. It is ideal for mounting hooks, signs, numbers, pictures, cable trunking, bathroom and car accessories. The tape can be used for bonding wood, ceramic tiles, metal, brick, stone, plaster and most plastics. Size: 10 strips (19 mm x 40 mm).

The Unibond 781739 holds up to 2Kg per strip and is suitable for both interior and exterior use. It can withstand high temperatures up to 95 C for short periods of time, and is ideal for mounting hooks, signs, numbers, car number plates, pictures, cable trunking, bathroom and car accessories. The tape can be used for bonding wood, ceramic tiles, metal, brick, stone, plaster and most plastics. Size: 10 Strips (20 mm x 40 mm). Removable.

1 x Unibond No More Nails Original Tube 234g

Unibond No More Nails is a high strength grab adhesive that eliminates the need for nails and screws in many DIY and repair jobs. It is safe and easy-to-use, adheres to most building materials and can be used to fill minor gaps on uneven surfaces. No More Nails is ideal for fixing skirting boards, dado rails, architraves, coving, polystyrene mouldings, decorative wall panels, plasterboard, carpet and carpet grippers and worktops. Dries translucent.1 x Unibond No More Nails Invisible Cartridge 285g

1 x Unibond No More Nails Original Cartridge 365g

Unibond No More Nails Original Mini Tube 40ml Supplied in a handy mini tube.

Unibond No More Nails Exterior is a high strength adhesive that eliminates the need for nails and screws in many DIY and repair jobs. It provides one of the strongest initial grabs available from Unibond, for un-paralleled support for heavier objects. It is extremely versatile and adheres to most building materials. Dries white. Suitable for exterior use.

1 x Gorilla Heavy-Duty Grab Adhesive White 80ml.

1 x Gorilla Heavy-Duty Grab Adhesive Clear 270ml.

EVO-STIK EVOSS Strong Stuff Weatherproof Adhesive is a High performance, single component, moisture curing, Modified Silane (MS) Polymer based adhesive. Will bond most surfaces even if both are impervious. Will bond damp surfaces and may even be used underwater. It has a low odour and cures to form an elastic rubber, with almost no shrinkage and low hazard. Bonds to most surfaces. Size - C20 cartridge

EVO-STIK Gripfill Solvent Free is a high strength, gap filling adhesive. Can be used on a wide range of building materials; one surface must be porous. Suitable for interior use.

EVO-STIK Gripfill Xtra is a superior strength, gap filling adhesive. Can be used on a wide range of building materials; one surface must be porous. Suitable for interior and exterior use.

The Gripfill gap filling adhesive will bond to almost any surface with excellent strength including vertical applications. Evo-stik Gripfill is a solvent-borne, filled rubber resin adhesive, developed to bond virtually any rigid materials together, regardless of the evenness of the surface. Gripfill is a high strength, one part, gap filling adhesive specially formulated to bond a large variety of materials. Evo-stik Gripfill is suitable for interior and exterior use (provided bond is covered) Bonds: Wood, plywood, hardboard, chipboard, laminated plastic, brick, rigid insulation material (except polystyrene), metal, stone breeze block, ceramics, concrete, sand/cement screeds, plasterboard, cement composite boards, G.R.P

1 x EVO-STIK Sticks Like Clear 290ml

1 x EVO-STIK Sticks Like White 290ml

The EVO-STIK Sticks Like Turbo is a fast setting. superior strength, all weather adhesive, suitable for use on a wide range of building materials. It sets in just 15 minutes and can resist extreme temperatures and movement and will even stick to wet surfaces. For interior and exterior use.

This EVERBUILD PINKGRIP is a solvent free, environmentally friendly formulation, white version of the brand leading Pinkgrip Direct Bond Adhesive. It has all the unique benefits of Pinkgrip and will stick just about anything on a building site, without the need for under pinning, thanks to the product's no-slump formula.It can be used for - bonding dado rails, architraves, and skirting, fixing wall cladding direct to internal wall surfaces or timber battens and fixing battens directly onto walls without fastenings.The adhesive will bond carpet gripper systems to most floors, without the need for nails or tacks. it will also bond stair nosing to concrete, or wooden stairs. This solvent free formulation is used for securing aluminium or other skin panels to the framework, or portable industrial buildings, and caravans.Pinkgrip has excellent adhesion/bond strength and adheres to most common surfaces. The enhanced slump resistance allows for quick simple direct bonding, without the need for temporary support in many applications.The product has a good “nip off” quality to prevent messy stringing of adhesive, and its high solids formulation gives excellent gap filling properties without shrinkage. The extended open time allows for easy repositioning after fixing.It will adhere to damp surfaces, and can be cleaned up with water Pinkgrip which has no hazardous solvents.Specifications: Colour: White.Size: 380ml.

Colour: Natural

Colour: Grey.

1 x Everbuild Stixall Extreme Power Easi Squeeze White 80ml

1 x Everbuild Stixall Extreme Power Easi Squeeze Crystal Clear 80ml

Colour: Clear.

Colour: Brown.

Colour: Black.

Everbuild Pinkgrip SF direct bond solvent-free gap filling adhesive specifically formulated for the professional user. The product can be used to replace mechanical fixings in a wide variety of building and home improvement applications for bonding wood, brick, plaster, plasterboard, polystyrene, Styrofoam and most plastics, metals and numerous other surfaces and is designed primarily for internal use. Approximately 12 linear meters for a 6mm diameter bead.

Pinkgrip Dry Fix is a revolutionary new type of fast curing, adhesive foam that has been specially developed for the rapid installation of Plasterboard, Insulation Boards and other sheet materials such as Roof Decking and Floorboards. Pinkgrip Dry Fix provides significant labour saving and convenience benefits when compared to traditional dry wall adhesives. It will bond to most common building substrates; can be applied horizontally or vertically to boards, walls or battens/beams. The foam expands very minimally on application but enough to fill any gaps on uneven surfaces. Pinkgrip Dry Fix can be applied using an Everbuild Dry Fix Applicator Gun.

Sika Multi Stick MS is an exciting new grab adhesive based on new SPUR technology (Silyl-terminated PUR technology). This superior adhesive has the ability to bond virtually anything to everything in both wet and dry conditions, and even underwater or in the rain. With incredible initial grab, high bonding strength, and almost limitless applications and other benefits, no tradesman should be without a tube of this next generation adhesive. Capable of bonding to almost all materials, porous and non-porous, such as: Glass, Marble, Granite, Mirrors, Bricks, Stone, Plasterboard, Concrete, All Metals, All Hard Plastics, Ceramics, Fibreglass, Timber and much, much more. Including applications underwater.

Everbuild Maximum Torque Adhesive is the ultimate high grab building adhesive. The unique polymer blend gives incredible initial grab, typically double that of most grab adhesives on the market today, eliminating the need for temporary support in most applications. It has the ability to bond basically everything to anything in virtually all conditions, even under water or in the rain. Cures to form a tough flexible elastic rubber, which also makes it suitable for use as a sealant.

Everbuild Griptite is a ready to use gap filling and panel adhesive based on a high bond strength synthetic rubber/resin mix in a solvent carrier. Adheres to most common surfaces inside and outside the home. Bonds to wood, plaster, plasterboard, carpet, carpet grippers, metal, glass, ceramics, brick, concrete, cork, PVCu and certain plastics. Benefits;Solvent based formula - quick drying / high early bond strength.Excellent adhesion/bond strength - adheres to most common surfaces.Good early grab properties - usable in both vertical and horizontal positions.High solids formulation - excellent gap filling properties without shrinkage.Suitable for use where both surfaces are non-porous.Excellent external weathering properties-Suitable for exterior use Ideal for:Bonding dado rails, architraves and skirting. Fixing parquet and cork flooring.Fixing wall cladding direct to internal wall surfaces or timber battens.Fixing battens directly onto walls without fastenings.Bonding carpet gripper systems to most floors without the need for nails or tacks.Bonding stair nosing to concrete or wooden stairs.Fixing polyester, wood, PVCu or metal thresholds.Fixing nameplates, plastic boxes, decorative frames, wall sockets and junction boxes to most surfaces.Securing aluminium or other skin panels to the framework or portable industrial buildings and caravans. Limitations;Do not use on damp surfaces: use EVERBUILD GUN A NAIL.Do not use as a mirror adhesive: use EVERBUILD MIRRORMATE Do not use on polystyrene/styrofoam/expanded polyurethane - use EVERBUILD GUN A NAIL.Heavy materials (greater than 8kg per sq meter) must be supported for at least 8-24 hours depending on size of item. Solvents present may attack sensitive plastics. If in doubt, rest a small area first. C4: 350ml.

Everbuild Gun A Nail Standard is a high strength, gap filling multipurpose building adhesive based on a tackified solvent free system for use in a wide variety of building and home improvement applications. Gun A Nail Standard can be used where at least one of the substrates to be bonded is porous. BENEFITS- Solvent-free - environmentally friendly formulation- Excellent adhesion/bond strength - adheres to most common surfaces.- Exceptional early grab properties - usable in both vertical and horizontal positions. - High solids formulation - excellent gap filling properties without shrinkage.- Extended open time - allows for easy repositioning after fixing- Will adhere to damp surfaces.- Water clean up - no hazardous solvents. AREAS FOR USE- Bonding dado rails, architraves and skirting- Fixing wall cladding direct to internal wall surfaces or timber battens- Fixing battens directly onto walls without fastenings- Bonding carpet gripper systems to most floors without the need for nails or tacks- Bonding stair nosing to concrete or wooden stairs- Securing aluminium or other skin panels to the framework or portable industrial buildings and caravans.

Pinkgrip Dry Fix Applicator Gun - for use with Pinkgrip Dry Fix Fast Cure Dry Wall Adhesive.

Everbuild Clear Fix is a clear hybrid polymer grab adhesive that has the ability to bond just about everything in both interior and exterior applications. With added UV stabilisers to ensure the product doesn't yellow over time, Clear Fix is the ideal choice for applications where the colour of the product may be seen. Clear Fix is a versatile product which can be used in almost every application - even when immersed under water! It is quick curing, resistant to temperature extremes, over-paintable and totally water and weatherproof. Size: 290ml.Colour: Clear.

1 x Gorilla Heavy-Duty Grab Adhesive - White 290ml

Colour: White.

Pinkgrip is a revolutionary direct bond adhesive specifically formulated for the professional user, using polymers at the leading edge of adhesive technology. Pinkgrip will stick just about anything on a building site that needs sticking. Its amazing grabbing strength not only removes the need to pin under the work piece to prevent slumping, but its revolutionary initial Direct Bond eliminates the need for double stick methods. Pinkgrip can be used inside and outside and adheres to just about every building substrate, providing the following key benefits: - Enhanced slump resistance for quick and simple direct bonding to most substrates without the use of temporary supports in most applications. - Excellent early and ultimate adhesive strength on porous substrates. - Excellent gap filling properties to accommodate uneven surfaces. - Good nip off qualities to prevent messy stringing of the adhesive Size: 350ml cartridge.

The Everbuild Instant Nails is a high strength, solvent-free, gap filling multi use adhesive that provides a quick grab and replaces mechanical fixings in many home improvement applications. Dries white and may be overpainted if required. Instant Nails should be at room temperature when you begin using the product. If Instant Nails has been stored in cool conditions it should be placed in a warm room/bucket of warm water before use to gently heat up to working temperature. Do NOT apply Instant Nails at temperatures below4C.

Tacwise Hot Melt Glue Sticks are made from high-quality materials and are ideal for a range of applications from arts/crafts and DIY, to plastic, glass and paperwork. The clear, fast-heating sticks are compatible with the Tacwise H4-7 Cordless Glue Gun as well as many other leading brands taking 7mm sticks. Each box contains 100 glue sticks which are supplied in a UK Royal Mail large letter sized box, making it easier to send/receive. Specification: Diameter: 7mmLength: 150mmPack Quantity: 100

The Stanley STA1GS20DT Dual Temp Glue Sticks 100mm (4 inch) comes in a pack of 24.

The STA1GS10DT Dual Temp Glue Sticks have the following specifications: Length: 100mm (4 inches). Diameter: 7mm. Pack of 24.

Colour: Transparent.Diameter: 7mm.Length: 65mm.Pack size: 125g (Approx 46 glue sticks)Compatible with the Rapid EG Point Glue Gun.

The Rapid GEN-T Glue Sticks are supplied in a 2.5kg bag. Size: 12mm Diameter x 295mm Length.

1kg Bag.

The Rapid GEN-T Glue Sticks are supplied in a large 10kg box. Size: 12mm Diameter x 190mm Length. 1kg = Approx 1090 sticks

Colour: Transparent.Diameter: 12mm.Length: 94mm.Pack: 125g (13 sticks). For use with the Rapid EG212, EG250, CG270, BGX300 and EG310 glue guns.

Colour: White.Diameter: 12mm.Length: 94mm.Pack: 125g (13 glue sticks). For use with the Rapid EG212, EG250, CG270, BGX300 and EG310 glue guns.

Bostik DIY Hot Melt Glue Sticks can be used with the DIY Hot Melt Glue Gun for an ultra-strong, long-lasting bond in seconds on a wide range of materials, and are easy to insert. Specification Length/Diameter: 100 x 12mm

Bostik Handy Glue Sticks can be used with the Handy Hot Melt Glue Gun for an ultra-strong, long-lasting bond in seconds on a wide range of materials, and are easy to insert. Specification Length/Diameter: 102 x 7mm

Bostik Handy Glue Sticks can be used with the Handy Hot Melt Glue Gun for an ultra-strong, long-lasting bond in seconds on a wide range of materials, and are easy to insert. Length/Diameter: 300 x 11mm

Bostik DIY Hot Melt Glue Sticks can be used with the DIY Hot Melt Glue Gun for an ultra-strong, long-lasting bond in seconds on a wide range of materials, and are easy to insert. Length/Diameter: 100 x 7mm

Pack of 6 slow set hot melt glue sticks. They are 102mm (4in) long but can be snapped in half if required, they are ideal for plastics, fabrics, foam, leather and many other materials.

Pack Quantity: 24.

Pack Quantity: 12.

Length. 102mm (4in)Suitable for use with models TR550P and TR200Pack Quantity of 24.

Arrow All Purpose Glue Sticks 102mm / 4 inch Pack of 6

Pack Quantity of 456. (Approx.)

Arrow AP10 All Purpose Glue Stix 254mm Pack of 12

The Tacwise H4-7 Hot Melt Cordless Glue Gun is ideal for a wide range of applications, including DIY, arts and crafts, fabrics, wood, plastic and leather. Made from impact and high heat resistant material, the free-standing gun is quick to heat up and features a handy auto turn-off after 5 minutes of non-use. With an automatic LED light for precision, and a comfortable, contoured trigger, this gun is the ideal choice for DIY/everyday usage. It also boasts a rechargeable, fully integrated 4V lithium-ion battery, making wires a thing of the past. Supplied with: 1 x USB Charging Cable, 30 x Tacwise Hot Melt Glue Sticks and 1 x Handy Neoprene Storage Bag. Backed by a 2-year guarantee when using Tacwise Hot Melt Glue Sticks.

The Stanley Heavy-Duty Glue Gun with convenient fold down stand for use between applications. Uses dual melt 11.3mm glue sticks for full range of materials, and has a high/low melt switch. Input Power: 25W.Glue Sticks: 11.3mm Dual Melt.

The Stanley FatMax Hi Output Professional Glue Gun 200W 240V with fast warm up which means it is ready to use in just 60 seconds. Its ceramic element heats up quicker and holds heat longer with a 1133g per hour output. The standby mode takes 30 seconds to get back to working temperature. The hibernate mode stores heating after 30 minutes of non-use. The gun has a dual colour LED, red when below 170 and green when ready to use. Supplied with: 6 x 12mm General Purpose Glue Sticks.6 x 12mm Formula II Super Strength Glue Sticks.6 x 12mm Dual Temperature Glue Sticks. Specification Input Power: 200W. (135-210).Heating Time: 1 Minute.Glue Output: 1133gr/hour.Glue Sticks: 12mm Dual Temp.

The Rapid EG Point Glue Gun is a mini glue gun for precise work. It is ideal for DIY and craft. The glue gun can be used cordlessly for 3-4 minutes before reconnecting to the detachable cable for difficult to reach places or awkward angles. It operates between 170 to 200C and has an improved, built-in stand for better stability. Compatible with Rapid 7 mm glue sticks. 2 year guarantee. Input Power: 10 (80W).Heating Time: 10 mins.Tip Diameter: 0.7mm.Glue Output: 150g/h.Material: ABS and metal.

The Rapid EG380 Glue Gun is a powerful gun designed for industrial use, equipped with a 2-heater system with a total of 400 watts providing a glue output of 2200 gr/hour. It is ideal for use on PVC, for sealing cables and tiles, electronics and electrics, furniture and wood, manual carton sealing, trade exhibits and decoration. It can be used with both low and high temperature 12mm diameter glue sticks and the temperature is adjustable from 130 to 230C, the temperature settings are 130 C, 150 C, 170 C, 190 C, 210 C and 230 C Its strong feeding mechanism allows a higher glue output per trigger stroke for intensive use, and it has a 4-minute heating time. Interchangeable nozzles (available to purchase separately) and an adjustable stand allow this glue gun to be used for all types of jobs. The smooth-4 finger soft grip trigger and ergonomic lightweight design ensures comfort over long term use and reduces the effort required. Comes with a 2-year guarantee. SpecificationInput Power: 400W.Working Voltage: 220V-240V.Heating Time: 1 min at 130 C, 3 min at 210 CTemperature Settings: 130 C, 150 C, 170 C, 190 C, 210 C and 230 CGlue Output: 2200gr/hour.Glue Stick Diameter: 12mm.Regulation: Mechanical Thermostat.Nozzle: 3.5 mm, exchangeableCord Length: 3.5m.

The Rapid EG340 Glue Gun is designed for pro-industrial users who need a powerful glue gun for high intensity use that works with different type of glues. It is ideal for use on PVC, for sealing cables and tiles, electronics and electrics, furniture and wood, manual carton sealing, trade exhibits and decoration. The EG340 is equipped with a heater system of 220 watts, a very accurate, low effort 4-finger soft grip trigger mechanism allowing the best ratio pressure/transfer into the melting chamber and a soft grip handle for high comfort. It can be used for both low and high temperature 12mm diameter glue sticks and the temperature is adjustable from 120 to 220C, the temperature settings are 120C, 145C, 170C, 195C and 220C. The high glue output of 1400g/hour is ideal for intensive use and the 2-minute heating time ensures it is ready to use when needed. Interchangeable nozzles (available to purchase separately) and an adjustable stand allow this glue gun to be used for all types of jobs. Comes with a 2-year guarantee. SpecificationInput Power: 220W.Working Voltage: 220V-240V.Heating time 1 min at 130 C, 3 min at 210 CTemperature Settings: 120/145/170/195/220C.Glue Output: 35g/min - 1400gr/hour.Glue Stick Diameter: 12mm.Regulation: Mechanical Thermostat.Nozzle: 3.0 mm, exchangeableCord Length: 2.5m.Supplied with a fixed and a mobile stand

The Rapid EG320 Glue Gun is a compact, lightweight and versatile gun for use in many conditions. It is ideal for use on PVC, for sealing cables and tiles, electronics and electrics, furniture and wood, manual carton sealing, trade exhibits and decoration. The EG320 is equipped with a heater system of 120 watts and a low effort, 4 finger soft grip trigger mechanism for comfort of use. It is for use with 12mm diameter glue sticks and has a pre-set, fixed temperature of 195C which is self-regulated. The glue output of 1000g/hour is ideal for intensive use and the 3-minute heating time ensures it is ready to use when needed. Interchangeable nozzles (available to purchase separately) and an adjustable stand allow this glue gun to be used for all types of jobs. SpecificationInput Power: 120W.Working Voltage: 220V-240V.Heating Time: 4 minutes (195C).Temperature Settings: 195C.Glue Output: 1.000g/h.Glue Stick Diameter: 12mm.Regulation: Self-regulated.Nozzle: 3.0 mm, exchangeableCord Length: 1.75m.

The Rapid EG212 Multi-Purpose Glue Gun is ideal for DIYers and hobbyists. It can be used on all kinds of material for decoration and simple repair jobs. Its compact size and balance allow it to be used in all conditions and at all angles. The bi-material, soft grip trigger mechanism and adjustable stand ensures comfort of use, and the nozzle is protected by silicone. This glue gun is for use with 12mm glue sticks and has a 3–6-minute heating time and 250g/hour glue output. SpecificationInput Power: 200W.Working Voltage: 220V-240V/50Hz.Heating Time: 3-6 minutes.Glue Output: 250g/hour.Glue Stick Diameter: 12mm.

The Rapid EG111 Glue Gun is a perfect all-round glue gun for DIY jobs and easy repairs around the home. It is compatible with all Rapid 12mm diameter glue sticks. It has a lightweight design and is easy to use, it heats up in less than 5 minutes. The silicone nozzle protects against burns and it has a removable metal stand, for better stability when standing. Comes with a 2 year guarantee. Supplied with 500g of transparent 12mm diameter x 190mm length glue sticks. Specifications: Working Voltage: 220V-240V/50Hz.Heating Time: 5 minutes max. Glue Stick Diameter: 12mm.

The Rapid AC300 Spare/Replacement Li-Ion Battery Pack, specially designed for use with the Rapid BGX300 Cordless Glue Gun. The glue gun can now be used while a spare battery is charging which offers more flexibility and performance. The Rapid BGX300 Glue Gun is an innovative, cordless glue gun ideal for decoration, repair, baseboards, light frames and furniture. SpecificationBattery Capacity: 2.6Ah.Battery Chemistry: Li-ion.Voltage: 7.4V.

This Rapid BGX300 is a versatile cordless Lithium-Ion powered glue gun. It is designed for precision operation around the house, the BGX300 features patented heating technology and offers up to 60 minutes cordless operation before recharging is required. It features a ready-to-use indicator light and adjustable gluing stand for application in the optimal position. It is ideal for decorating, repairing baseboards, light frames and furniture. Includes: 1 x 7.2V 2.6Ah Li-ion Battery. Specification:For 12 mm glue sticks250 g/h glue output3-6 min heating timeDimensions (W x H x D mm) 256 x 315 x 66Weight: 0.69kg

Heavy-duty glue gun, ideal for DIY tasks and household repairs with an ultra strong long lasting bond. It has constant thermostatic control, safety warning light and trigger control to glue on demand. Includes 2 glue sticks and CE approved. Specification: Input Power: 55WGlue Stick Diameter: 12mm

The Bostik Handy Hot Melt Glue Gun is ideal for hobbies and light household repairs. Compact and easy to use. Its trigger control allows for consistent application and it comes with its own retractable stand. Includes 2 glue sticks. Specification Input Power: 45WGlue Stick Diameter: 7mm

Loctite Rear View Mirror Bonder is a unique system for bonding rear-view mirrors and all window mounted aerials. Supplied as a single shot pack, that bonds in 30 seconds with no need for liquid activators. Ideal for any glass to metal application. Size: 0.5ml

The Large (43g) Pritt Stick is well-suited for frequent users and for gluing large areas.

The Medium (22g) Pritt Stick is an all-rounder for creative and smart paperwork in office, school and at home.

The Small (11g) Pritt Stick is well-suited for gluing smaller areas, edges, and corners.

The Loctite 60 Second All Purpose Glue has a colourless, ultra-thick gel formula that prevents dripping and bonds all materials within 60 seconds. Objects are repositionable for up to 40 seconds. It builds up a strength of100kg/cm2 within 24 hours. The glue will bond to most materials, porous and non-porous, as well as flexible materials and objects exposed to stress. It is ideal for larger applications thanks to its tailored formula and its bigger tube.

The GRGGG60 Gorilla glue comes in the following: Size: 60ml

The GRGGG500 Gorilla glue comes in the following: Size 500ml

The GRGGG250 Gorilla glue comes in the following: Size: 250ml

The GRGGG115 Gorilla glue comes in the following: Size: 115ml

The GRGGG1 Gorilla glue comes in the following: Size: 1 Litre

Everbuild STICK2 All-Purpose Clear Adhesive is a strong, clear, quick drying adhesive suitable for a variety of household repairs and hobby uses. Will stick ceramics, porcelain, pottery, wood, card, paper, most plastics, leather, cork, linoleum, rubber, stone, glass, metals and dense fabrics to both themselves and each other. Always open and use this product over a protected work surface. Surfaces to be bonded must be clean, dry and free from dust. Use only in well ventilated areas. Do not breathe vapour. POROUS SURFACES (fabrics, ceramics etc.) Unscrew cap and spread a thin even layer of adhesive onto one surface. Press two surfaces together firmly. NON-POROUS SURFACES (plastics, metals etc.) Improve adhesion by abrading both surfaces with sandpaper. Unscrew cap and spread a thin even layer of adhesive onto both surfaces. Allow adhesive to dry to a tough tacky finish (about 5-10 mins) then press both surfaces together firmly.In both cases, full strength is obtained after 24 hours at 20CReplace cap immediately after use to keep adhesive usable.

1 x Bostik All Purpose Adhesive 50ml

1 x Bostik All Purpose Adhesive 20ml

Loctite All Purpose Adhesive is a quick drying clear glue that's an ideal household adhesive for those unforeseen repairs. Sets in minutes, is transparent and is particularly suitable for use on fabrics, card, cork, felt and most plastics.

1 x Evostik Flooring Adhesive 1 Litre

Everbuild Lumberjack 550 Floor Adhesive is a high specification, hybrid polymer, cartridge applied adhesive specially designed for fixing all types of wooden floors directly onto all common substrates. It is a 100% active solvent and water-free, and therefore will not cause warpage of wood. Has rapid setting properties and remains permanently flexible. It is also suitable for use with underfloor heating, and has excellent acoustic properties. Colour: Buff.Size: 300ml.

The Everbuild Coving adhesive is a high strength, solvent free, adhesive providing a quick grab for fixing polystyrene, plaster coving, and cornices to sound porous surfaces. The 290ml product will also act as a sealant for filling the gaps between individual lengths of coving.This coving adhesive dries white and can be painted over when dry.The solvent free and environmentally friendly formula has excellent adhesion/bond strength and adheres to most common coving surfaces, and has early grab properties, usable in both vertical and horizontal positions.The high solids formulation gives it excellent gap filling properties, it will adhere to damp surfaces, can be cleaned up with water and containing no hazardous solvents, Uses include:Fixing and sealing polystyrene coving, ceiling centres tiles and other decorative polystyrene products to sound surfaces.Fixing plaster coving.Filling gaps between coving sections.Specifications: Colour: White.Size: 290ml.

Size: Tube 50ml

Size: 500ml Bottle.

Size: 125 ml Bottle.

1 x Gorilla Glue Clear 50ml

1 x Gorilla Glue Clear 170ml

1 x Gorilla Glue Clear 110ml