This Milwaukee Hand Tools VDE Diagonal Cutter has the following specification: Total Length: 160mmCutting Capacity: Hard Wire 2mm; Soft Wire 6mm; Al Cu Cable 11mmWeight: 210g

This Milwaukee Hand Tools VDE Diagonal Cutter has the following specification: Total Length: 145mmCutting Capacity: Hard Wire 1.7mm; Soft Wire 5mm; Al Cu Cable 8mmWeight: 160g

The Milwaukee Hand Tools VDE Long Nose Pliers have a fully forged, hardened and tempered head with 45 angled, flat-round jaws. Grey titanium surface finish that is non-reflective and provides maximum corrosion resistance. Ideal for holding, gripping, bending and cutting work. Precision machined joint for maximum power transmission with optimum leverage for easy and effortless work. Fitted with ergonomic handles that have a soft grip for comfortable handling and a good grip. VDE (DIN EN/IEC 60900) certified: tested up to 10,000V and guaranteed to 1,000V. Tested against cold to -40?C. Specification: Total Length: 205mmCutting Capacity: Hard Wire 2.3mm; Soft Wire 3.9mmWeight: 200g

The Milwaukee Hand Tools VDE Long Round Nose Pliers have a fully forged, hardened and tempered head. With a grey titanium surface finish that is non-reflective and provides maximum corrosion resistance. Ideal for holding, gripping, bending and cutting work. Precision machined joint for maximum power transmission with optimum leverage for easy and effortless work. Fitted with ergonomic handles that have a soft grip for comfortable handling and a good grip. VDE (DIN EN/IEC 60900) certified: tested up to 10,000V and guaranteed to 1,000V. Tested against cold to -40?C. Specification: Total Length: 205mmCutting Capacity: Hard Wire 2.3mm; Soft Wire 3.9mmWeight: 200g

This Milwaukee Hand Tools VDE Cable Cutter has the following specification: Cutting Capacity: Al Cu Cable 25mmOverall Length: 210mm

This Milwaukee Hand Tools VDE Cable Cutter has the following specification: Cutting Capacity: Al Cu Cable: 16mmOverall Length: 160mm

The Milwaukee Hand Tools Nipping Pliers have a forged design and an iron carbide cutting edge for increased tool durability. With a black oxide finish that protects against rust. Smooth head design, will not mark the surface during pulling and prying applications. The handles are fitted with comfort grips that are more comfortable than dipped plastic, these grips will not peel.

These Milwaukee Hand Tools Quick Adjust Water Pump Pliers have the following specification: Overall Length: 300mm (12in)Max. Deburring: Handles 25mm; Head 70mmMax. Cutting Capacity: Nut Size AF 50mm; Tube Pipe 60mm

These Milwaukee Hand Tools Quick Adjust Water Pump Pliers have the following specification: Overall Length: 250mm (10in)Max. Deburring: Handles 25mm; Head 51mmMax. Cutting Capacity: Nut Size AF 36mm; Tube Pipe 42mm

These Milwaukee Hand Tools Quick Adjust Water Pump Pliers have the following specification: Overall Length: 200mm (8in)Max. Deburring: Handles 25mm; Head 38mmMax. Cutting Capacity: Nut Size AF 30mm, Tube Pipe 32mm

These Milwaukee Hand Tools Diagonal Pliers have the following specification: Cutting Capacity: Medium/Hard Wire 3.0mm; Soft Wire 4.0mmJaw Length: 26mmTotal Length: 180mm

These Milwaukee Hand Tools Diagonal Pliers have the following specification: Cutting Capacity: Medium/Hard Wire 2.5mm; Soft Wire 4.0mmJaw Length: 22mmTotal Length: 160mm

The Milwaukee Hand Tools Cable Cutting Pliers offer best in class cutting quality with bevelled jaw heads for accurate, smooth cable shearing. The forged design provides increased tool durability, especially in tough on-site environments. With a black oxide finish for protection against rust. The handles are fitted with comfort grips, that are more comfortable than dipped plastic. These grips will not peel. Specification: Max. Cutting Capacity: Aluminium 12mm/107mm; Cable 10mm/67mm

The Milwaukee Hand Tools Long Nose Pliers are made from chrome vanadium steel for increased durability and good rust protection. With laser hardened cutting edges, jaws extra hardened to 64 HRC. The serrated jaws also feature an integrated nail puller, wire cutter and deburring ribs for pipe up to 20mm. The handles are fitted with ergonomic, overmoulded grips for added comfort. These pliers are ideal for gripping, bending and adjusting in restricted areas. Specification: Wire Cutting Capacity: Medium/Hard Wire 2.5mmJaw Length: 51mmTotal Length: 210mm

The Milwaukee Hand Tools Lineman's Pliers are made from chrome vanadium steel for increased durability and rust protection. Laser hardened cutting edges, jaws additionally hardened to 64 HRC, that can cut wire, bolts, screws and nails. With a serrated gripping zone for strong gripping and pulling. The head also features an integrated nail puller, crimping facility and deburring ribs for pipe up to 25mm. High leverage design with long handles for maximum cutting power and leverage. Ergonomic overmoulded grips provide a secure grip, added comfort and tool control. Specification: Cutting Capacity: Medium/Hard Wire 3mm; Soft Wire 4.6mmTotal Length: 250mm

Milwaukee Hand Tools Offset Metal Aviation Snips for long straight cuts. Ideal for narrow radius cuts and notch cuts.

Milwaukee Hand Tools Metal Aviation Snips for long straight cuts. Ideal for narrow radius cuts and notch cuts.

The Milwaukee Hand Tools Metal Aviation Snips are made from forged alloy steel (Cr steel) that is chrome plated for increased lifetime. Extra hardened to 65 HRC. Serrated cutting edges prevent slippage when cutting. Compound leverage action, the torsion spring opens jaws automatically during cutting for faster cutting action and less fatigue work. The handles feature ergonomic and durable overmoulded grips with thumb and forefinger slots for increased comfort and less fatigue. Allows user to push through sheet metal with ease with less risk of cutting oneself. Flush slimline design with a one-hand locking mechanism. Triple cutting direction identification: on the head, handle and by colour coded handle. Contains: 1 x Metal Aviation Snips Left Cut, 1 x Metal Aviation Snips Right Cut 1 x Metal Aviation Snips Straight Cut. Specification: Edge Length: 31mmMax. Cutting Capacity: Aluminium 1.0mm; Stainless Steel 0.6mm; Steel 1.0mmOverall Length: 260mmWeight: 430g

Milwaukee Hand Tools Offset Metal Aviation Snips for short straight cuts. Ideal for narrow radius cuts and notch cuts.

Milwaukee Hand Tools Metal Aviation Snips for short straight cuts. Ideal for narrow radius cuts and notch cuts.

Milwaukee Hand Tools Offset Metal Aviation Snips for short right shaped cuts. Ideal for narrow radius cuts and notch cuts.

Milwaukee Hand Tools Metal Aviation Snips for short right shaped cuts. Ideal for narrow radius cuts and notch cuts.

Milwaukee Hand Tools Offset Metal Aviation Snips for short left shaped cuts. Ideal for narrow radius cuts and notch cuts.

Milwaukee Hand Tools Metal Aviation Snips for short left shaped cuts. Ideal for narrow radius cuts and notch cuts.

The Milwaukee TORQUE LOCK™ Curved Jaw Locking Pliers provide faster set-up and easy release when clamping round material. For a stronger and more secure grip, extra force can be applied to the TORQUE LOCK™ screw, which can also be used for hanging/storage purposes. The curved hardened jaws provide a better grip force on job site materials. Chrome plated finish increases tool life by reducing corrosion for rust protection. Traditional release lever design for job site convenience.The Milwaukee Hand Tools TORQUE LOCK™ Curved Jaw Locking Pliers have the following specification: Length: 254mm(10in)Capacity: 51mm

Size 165mm (6 1/2 in).Spring return

Size: 165mm (6 1/2 in).

Maun Flat Nose Pliers with smooth jaws for a firm grip without damaging delicate pieces. Perfect for working with jewellery and manipulating or straightening soft wire. Jaws move in parallel throughout use and grip securely along their whole length. They are able to manipulate, straighten and remove kinks in wire. Built to last, with a robust construction and rust-proof finish. The jaws have been case hardened to HRC 57 for added durability. Wire can also be threaded down throat of plier. Zinc-plated handles with detailing provide added grip. A workbench essential, for use with soft metals and other delicate materials. Ideal for: jewellery makers, manufacturers of delicate pieces, hobbyists and craft workers. Made in England. Conforms to BS 3087-7:1996, ISO 5747:1995. Comes with a standard 12 months' warranty. Register your tool to extend this to 2 years. Specification: Overall Length: 140mmJaw Opening: 10mmJaw Width: 8mmUsable Jaw Length: 28mm

Maun Flat Nose Pliers with serrated jaws for a vice-like grip on square and hexagonal fastenings. Jaws move in parallel throughout use and grip securely along their whole length. They are able to manipulate, straighten and remove kinks in wire. Built to last, with a robust construction and rust-proof finish. The jaws have been case hardened to HRC 57 for added durability. There is a V-slot to feed and hold wire and rod securely along jaw length. Wire can also be threaded down throat of plier. Zinc-plated handles with detailing provide added grip. A toolbox essential, with rugged construction, ideal for: electrician's, field technician's, field and manufacturing maintenance engineer's and serious DIY-ers. Made in England. Conforms to BS 3087-7:1996, ISO 5747:1995. Comes with a standard 12 months' warranty. Register your tool to extend this to 2 years. Specification: Overall Length: 160mmJaw Opening: 14mmJaw Width: 9mmUsable Jaw Length: 34mm

These Maun Snipe Nose Smooth Jaw Parallel Pliers are perfect for delicate working with small items, or in a restricted space. They are also useful for working with jewellery and manipulating or straightening soft wire. They are built to last with a robust construction and rust proof finish. The jaws case is hardened to HRC 57 for durability and the handles are zinc plated, with detailing for added grip.Length: 125mm.Jaw Opening: 10mm.Useable Jaw length: 30mm.

These Maun Snipe Nose Pliers have a serrated jaw for improved grip. They are ideal for work in confined areas. Length: 125mm (5in).

The Maun Ratchet Cable Cutter provides unrivalled cutting performance. Ratchet controlled to easily cut copper, aluminium and steel wire armoured (SWA) cables. Its hinged blade allows you to cut anywhere along the cable, even in tight spaces. Made to last, with a robust construction and rust-proof finish. Its precision-ground steel cutting blades are hardened and tempered to HRC 54 for durability. The blade is held in place by each ratchet tooth. Fitted with plastic handle grips for added comfort. A release lever frees blade from cable at any time during the cutting process. Ideal for: electrician's, machine service engineers, telecoms engineers and serious DIYers. Made in England. Comes with a standard 12 months' warranty. Register your tool to extend this to 2 years. Specifications Capacity: Copper/Aluminium Cables: up to 30mm diameterSteel Wire Armoured (SWA) Cable: up to 20mm diameterOverall Length: 250mm (10in) Will NOT cut catenary cables or any cable with central steel strand.

These Maun End Cutting Nippers are suitable for repetitive cutting of hard wire. The high leverage design cuts the wire with minimal effort. The induction hardened cutting edges to HRC 64 offer durability and a long-life service, they give an unrivalled cutting performance and easily cuts wires close to objects. They have precision ground sharp cutting jaw edges which will cut through a range of hard materials including - springs, nails, rivets and bolts. These cutters are built to last with a robust construction and rust proof finish. The compound lever action multiplies hand force by 14 for less cutting effort. The handles are zinc plated with detailing for added grip, and have a long-lasting return spring. The applications include - repetitive top cutting of springs in mattress and bed production, and wire spring making. The nippers also are useful for cutting hard wire in various metal-fabrication operations (such as annealed tie wire used on reinforced rods or braided reinforced concrete mesh). They are suitable for skilled tradespeople with demanding standards and serious DIY-ers, made in England. Conforms to BS 3087-7:1996, ISO 5747:1995. Comes with a standard 12 months' warranty. Register your tool to extend this to 2 years. Specification: Overall Length: 150mm (6in).Cutting Capacity: Piano Wire 1.6mm , Hard Wire 2.0mm .

Maun Diagonal Cutting Pliers with Zinc-plated handles and soft plastic grips for added comfort Specification: Overall Length: 160mm (6.1/4in)Jaw Opening: 10mmJaw Width: 8mmCutting Capacity: Piano Wire 2.0mm , Hard Wire 2.5mm , Soft Wire 4.0mm

Maun Diagonal Cutting Pliers with Zinc-plated handles and detailing for added grip. Specification: Overall Length: 160mm (6.1/4in)Jaw Opening: 10mmJaw Width: 8mmCutting Capacity: Piano Wire 2.0mm , Hard Wire 2.5mm , Soft Wire 4.0mm

Maun Diagonal Cutting Pliers with Zinc-plated handles and detailing for added grip. Specification: Overall Length: 140mm (5.1/2in)Jaw Opening: 10mmJaw Width: 8mmCutting Capacity: Piano Wire 1.6mm , Hard Wire 2.0mm , Soft Wire 3.0mm

This Maun Shear Nose Soft Wire Cutter is ideal for the horticultural industry and craft work. It will easily cut up to 3mm diameter of soft wire, and is comfortable, easy to use, with a high leverage design for minimal effort when cutting. This cutter has a compact, lightweight design and has a double action cutter for trimming wire ends to equal lengths. The jaws are machine ground, and its case is hardened to HRC57 for durability. The cutter has zinc plated jaws and handles, with detailing for added grip. Length: 100mm.Width: 30mm.Cutting Capacity: soft wire 3mm diameter.

The Maun Eyelet Puncher Fixing Pliers combine two jobs in one sturdy tool. Punch through materials and fix eyelets in one smooth operation. Built to last, with a robust construction and rust-proof finish. The jaws feature tapered bushes for precision setting of the eyelet dies. Eyelet dies are case hardened to HRC 57 for durability. The Zinc-plated handles feature detailing for added grip and a long-lasting return spring. Use this eyelet puncher to punch and fix eyelets into thin materials such as fabric, leather, canvas, thin plastics and card. Designed for use with 4mm (5/32in) inside barrel diameter eyelets ONLY. Made in England. Comes with a standard 12 months' warranty. Register your tool to extend this to 2 years. Specification: Overall Length: 200mm Useable Jaw Length: 35mm1 x Maun Eyelet Puncher Fixing Pliers 165mm

These Maun Revolving Punch Pliers are lightweight and easy-to-use. Designed with a revolving drum for quick and easy punch selection. Punches lock firmly in place for assured accuracy and are hardened for increased durability. Features six different punch sizes. Easily select your punch with the rotating drum. Built to last, with a robust construction and rust-proof finish. Fitted with a strong return spring for easy operation. Made from strong but lightweight carbon steel. With zinc-plated handles with detailing for added grip. Ideal for making holes in soft materials, especially leather. Manufactured to Mauns design in Germany. Comes with a standard 12 months' warranty. Register your tool to extend this to 2 years. Specification: Punch Sizes: 2, 2.4, 2.8, 3.2, 4, 4.8mm

The Maun Stationers Punch will punch up to 25 sheets of 80g/m paper in one operation, providing a clean punch every time, even when piercing multiple sheets of paper. No more punch jamming in the pierced hole. Built to last, with a robust construction and rust-proof finish, this precision-ground punch is case hardened to HRC 57. The punch and handles are zinc plated, with detailing on handles for added grip. Fitted with a return spring for easy operation, and made in England. Specification: Punch Diameter: 6.4mm (1/4in).Jaw Length: 32mm (1.1/4in).Overall Length: 200mm (8.1/4in).

Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

Length (A): 112mm (4.1/2in). Blade length (B): 12.5mm (0.5 in). Head width (C): 12.5mm (0.5 in). Head depth (D): 6.0mm (0.24 in). Tip width: (F): 1.2mm (0.05 in). Cutting capacity: 0.3-1.6mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

Length (A): 110 mm (4.3/8 in). Blade length (B): 10mm (0.39 in). Head width (C): 10mm (0.39 in). Head depth (D): 6mm (0.24 in). Tip width: (F): 0.8mm (0.03 in).Cutting Capacity: 0.1-1.0mm. Cutting edge: Ultra flush. The Ultra flush cutter virtually eliminates the pinch that other cutters make. The cutters configure two flat planes, with a barely discernible line separating each of these planar surfaces. They are perfect for use in close tolerance electronic and medical device assembly, where concerns about final lead-end configuration and mechanical shock transmission are a top priority.

Length (A): 110mm (4.3/8 in)Blade length (B): 10mm (0.39 in). Head width (C): 10mm (0.39 in). Head depth (D): 6mm (0.24 in). Tip width: (F): 0.8mm (0.03 in).Cutting Capacity: 0.1-1.25mm. Cutting edge: Flush Bevel. The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area - more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

Lindstrom Diagonal Cutting Size: 110mm.Type: Micro Bevel Nipper.

Lindstrom 7893 Supreme Snipe Nose Pliers are produced from high performance tool steel. These snipe nose holding pliers have a screw joint that minimises friction and maximises alignment of cutting edges. The handles have a return spring and are sleeved. The smooth jaws minimise the risk of damage and scratching surfaces. Length (A): 120mm (4.72 in). Jaw length (B): 20mm (0.79 in). Head width (C): 9mm (0.35 in). Head depth (D): 6mm (0.24 in). Tip width (E): 1.2mm (0.05 in). Tip depth (F): 0.8mm (0.03 in).

Lindstrom 7890 Supreme Flat Nose Pliers are produced from high performance tool steel. These holding pliers have a screw joint that minimises friction and maximises alignment of cutting edges. The handles have a return spring and are sleeved. The smooth jaws minimise the risk of damage and scratching surfaces. Length (A): 132mm (5.2 in). Jaw length (B): 32mm (1.26 in). Head width (C): 9mm (0.35 in). Head depth (D): 6mm (0.24 in). Tip width (E): 1.2mm (0.05 in). Tip depth (F): 0.8mm (0.03 in).

These Lindstrom Supreme Flat Nose Pliers are produced from high-performance tool steel. These holding pliers have a screw joint that minimises friction and maximises alignment of cutting edges. The handles have a return spring and are sleeved. The pliers' smooth jaws minimise the risk of damage and scratching to the wire. Length (A): 120mm (4.72in). Jaw length (B): 20mm (0.79in). Head width (C): 9mm (0.35in). Head depth (D): 6mm (0.24in). Tip width (E): 1.2mm (0.05in). Tip depth (F): 3.2mm (0.13in).

Length (A): 108mm (4.25 in).Blade length (B): 8mm (0.31 in). Head width (C): 10.5mm (0.41 in). Head depth (G): 15mm (0.59 in). Cutting capacity: 0.35-1.25mm. Head type: Double angled. Cutting edge: Flush. Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access. The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area - more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

Length (A): 108mm (4.25 in).Blade length (B): 8mm (0.31 in). Head width (C): 10.5mm (0.41 in). Head depth (G): 15mm (0.59 in). Cutting capacity: 0.35-1.25mm. Head type: Double angled. Cutting edge: Micro-bevel. Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

Length (A): 109mm (4.29 in). Blade length (B): 9mm (0.35 in). Head width (C): 9mm (0.35 in). Head depth (D): 6mm (0.24 in). Tip width: (F): 1.0mm (0.04 in). Cutting capacity: 0.2-1.25mm. Head type: TaperedCutting edge: Micro-bevel. The tapered head is the smallest of the standard cutting heads available. Not only does it taper on both sides, but also the underside is cut away, allowing the operater to gain access into some difficult areas. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

These Knipex High Leverage Concreter's Nippers have the following specification: Overall Length: 300mm (12in)Wire Cutting Capacities: Hard: 2.0mm, Medium: 3.8mmHead Width: 25mmWeight: 499g

These Knipex High Leverage Concreter's Nippers have the following specification: Overall Length: 250mm (10in)Wire Cutting Capacities: Hard: 1.8mm, Medium: 3.3mmHead Width: 25mmWeight: 350g

The Knipex High Leverage Concreter's Nippers offer substantially higher cutting performance as well as a damping of the cutting stroke after cutting the binding wire, two valuable ergonomic advantages for the user. They can twist and cut wire in one operation, making them fast, reliable and economical. Made from special tool steel that has been oil-hardened and tempered with an extra slim form. Making them ideal for tying submerged positioned steel rods. They provide a particularly high cutting capacity with minimum effort due to their optimum transmission ratio. High damping of the cutting stroke after cutting the binding wire reduces strain on tendons and muscles. These Knipex High Leverage Concreter's Nippers have a black atramentized head with polished tips and plastic coated handles. With the following specification: Overall Length: 250mm (10in).Wire Cutting Capacities: Hard: 1.8mm, Medium: 3.3mm.Head Width: 25mm.Weight: 350g.

These Knipex High Leverage Concreter's Nippers have the following specification: Overall Length: 300mm (12in)Wire Cutting Capacities: Hard 2.0mm; Medium 3.8mmHead Width: 25mmCutting Edge Length: 25mmWeight: 501g

These Knipex High Leverage Concreter's Nippers have the following specification: Overall Length: 250mm (10in)Wire Cutting Capacities: Hard 1.8mm; Medium 3.3mmHead Width: 25mmCutting Edge Length: 23mmWeight: 350g

KPX9901250 Concreter's Nipping Pliers. Length 250mm (10 in).

KPX9901220 Concreter's Nipping Pliers. Length 220mm (8 1/2 in).

These Knipex high-quality long nose pliers are made from fibreglass-reinforced plastic, which is fully insulated and provides protection against bridging for working on live parts up to AC 1,000V and DC 1,500V. These solid pliers also do not act on magnetic fields and are fully spark-free. They are ideal for meter assembly and meter blocking. In addition, they are excellent for use in chemically aggressive environments. The handles have a soft plastic zone for better grip. Tested up to 1,000 Volts and conforms to IEC 60900 DIN EN 60900.

These Knipex high-quality flat nose pliers are made from fibreglass-reinforced plastic, which is fully insulated and provides protection against bridging for working on live parts up to AC 1,000V and DC 1,500V. These solid pliers also do not act on magnetic fields and are fully spark-free. They are ideal for meter assembly and meter blocking. In addition, they are excellent for use in chemically aggressive environments. The handles have a soft plastic zone for better grip. Performance: Conform to IEC 609DD, and DIN EN 60900.

Knipex Twistor16 Self-Adjusting Pliers for crimping wire end sleeves according to DIN 46228 parts 1 4. Its square crimp profile has a high-capacity range of 0.14 to 16mm. The 360 rotatable crimping die has 8 tactile locking positions. Self-adjustment to the desired size of wire end sleeve. No crimping errors due to using the wrong crimping die or to an incorrect setting. Made from special quality, oil-hardened, chrome vanadium electric steel. With a slim head for increased accessibility and a lightweight design for operator comfort. Repetitive, high crimping quality due to integral lock (self-releasing mechanism) and the precisely calibrated pressure, this is done in the factory. Crimping of twin wire end sleeves up to 2 x 6mm possible. Specification: Capacity: 0.14-16.0mm or 26-5 AWGOverall Length: 200mmWeight: 478g

The Knipex 97 52 36 PreciForce Crimping Pliers offer good repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism). The crimping pressure has been set precisely (calibrated) in the factory and offers optimum transmission of force thanks to toggle lever for fatigue-reduced operation. The pliers have good handling thanks to their favourable handle position, low weight, compact design and ergonomically shaped handles. Made from special quality, oil hardened chrome vanadium electric steel. Applications: Insulated terminals and plug connectors.Capacity: 0.5-6.0mm AWG: 20-10.

For cable links and ferrules

For insulated terminals and plug connectors.

The Knipex 975110 is a Crimping Plier for western plugs. It is a professional tool for cutting, and stripping, unshielded ribbon telephone cables. This plier has a precise crimping process thanks to parallel crimping, and will crimp 6- and 8-pole Western plugs type RJ 11/12 (9.65mm width) and type RJ 45 (11.68mm width); long design. The Crimping Plier has a repetitive high crimping quality due to its integral lock (self-releasing mechanism) and has a length cutter and stripping knife for ribbon cables 6- and 12-mm length. With an additional stripping device for round cables, and chrome vanadium electric steel in special quality, oil-hardened, and cushion grip handles for added grip and user comfort. Capacity: RJ 11/12 (6-poles) 9.65mm RJ 45 (8-poles) 11.68mm.Weight: 340g.Length: 267mm.

With the possibility of crimping almost all currently available crimping connections with just one tool and state-of-the-art crimping pliers technology, the Knipex crimp system pliers solve almost all tasks in mobile and stationary crimping technology and are an excellent tool for professionals to use for standard crimping. The pliers have almost parallel crimping die movement and ensure repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism). The crimping pressure has been precisely calibrated in the factory and is re-adjustable. Different locators enable precise positioning of the connectors. Due to the lever action, the pliers ensure optimum transmission of force, resulting in reduced fatigue during operation. The handles are ergonomically designed for user comfort. The pliers are manufactured from chrome vanadium electric, oil-hardened steel. Crimping dies and case NOT supplied.

With the possibility of crimping almost all currently available crimping connections with just one tool and state-of-the-art crimping pliers technology, the Knipex crimp system pliers solve almost all tasks in mobile and stationary crimping technology and are an excellent tool for professionals to use for standard crimping. The pliers have almost parallel crimping die movement and ensure repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism). The crimping pressure has been precisely calibrated in the factory and is re-adjustable. Different locators enable precise positioning of the connectors. Due to the lever action, the pliers ensure optimum transmission of force, resulting in reduced fatigue during operation. The handles are ergonomically designed for user comfort.The pliers are manufactured from chrome vanadium electric, oil-hardened steel. The KPX9743200 crimp system pliers are supplied in a plastic case with a foam insert with recesses for crimping dies and locators. Supplied with an Allen Key. Crimping dies NOT supplied.

Knipex 97 33 Crimping Pliers with round magazine and 5 interchangeable profiles, which allow the professional electrician to quickly switch between crimping applications and to carry only one set of pliers. Factory calibrated for accurate and reliable crimping of connectors: Non-Insulated Open Plug: 0.5-6.0mm.Insulated Terminals, Plug and Butt Connectors: 0.5-6.0mm.End Sleeves (ferrules): 0.25-25mm. Non-insulated crimp terminals, tube and compression cable lugs in accordance with DIN 46234 and DIN 46235 and non-insulated crimp, butt and press connectors in accordance with DIN 46341 and DIN 46267. Sizes: 0.5 - 10.0mm.

The Knipex KPX973301 are crimping pliers with round magazine and 3 interchangeable profiles, allows the profesional electrician to quickly swith between crimping applications and carry only one set of pliers. The KPX973301 have been factory calibrated for accurate and reliable crimping of: Non-insulated open plug connectors (4.8 6.3 mm width) from 0.5 - 6.0mm; Insulated terminals plug connectors from 0.5 - 6.0mm; End sleeves (ferrules) from 0.25 - 6.0mm

These Knipex 97 21 Crimping Pliers for cutting cables, stripping wires and crimping insulated and non-insulated terminals, connectors and plug type connectors. With threaded holes for cutting copper and brass threaded screws. M2.6 - M3 - M3.5 - M4 - M5. For insulated terminals and cable connectors of 0.5 - 6.0mm.

This Knipex Wire Rope/Bowden Cable Cutter is fitted with ergonomic multi-component grips for added grip and comfort. Specification: Length: 190mmCutting Capacity: Multi-Stranded Cable: 7.0mm, Wire Rope: 6.0mm, Medium Hard Wire: 4.0mm, Piano Wire: 2.5mm

The Knipex 95 62 Series Wire Rope Cutters have a lightweight, compact design, however it is powerful enough to cut high strength wire rope. This cutter requires up to 30% less physical effort compared to wire rope cutters of the same length, thanks to the integrated opening spring. Made from ball bearing steel with a double-mounted box joint design for a high level of stability. The cutting edges have been additionally induction hardened, approx. 64 HRC. The cutters can be secured via a locking device for safe transportation. Ideal for cutting copper and aluminium cables, single and multiple wire cables and ACSR cable. Specification: Length: 160mmCutting Capacity (mm): Wire Rope: 4.0, Multi-Stranded: 6.0

This Knipex Wire Rope/Bowden Cable Cutter is fitted with ergonomically PVC coated styled handles for added grip and comfort. Specification: Length: 190mmCutting Capacity: Multi-Stranded Cable: 7.0mm, Wire Rope: 6.0mm, Medium Hard Wire: 4.0mm, Piano Wire: 2.5mm

The Knipex 95 36 Series VDE Cable Cutter has multi-component grips, VDE tested up to 10,000V and safe for work up to 1,000V. They conform to DIN EN / IEC 60900. It cuts through steel wire armoured cables with a diameter of up to 45mm, using one or two-handed operation. Not suitable for steel wire, ACSR cable or wire ropes. It has a low weight, compact design that is great for using in confined areas. The innovative three-stage ratchet-drive ensures high leverage for easy cutting in one-handed and two-handed operation. The steel cutting edges are hardened and precisely ground, ensuring a smooth, neat cut without crushing. They have a fixed handle with a support area and they are ideal for use in confined areas. Specification Cutting Capacity: 45mm / 380mmLength: 315mm

These Knipex Cable Cutters have and innovative three-stage ratchet-drive ensures high leverage for easy cutting in one-handed and two-handed operation. The steel cutting edges are hardened and precisely ground, ensuring a smooth, neat cut without crushing. Fitted with multi-component, soft grip handles that are lightweight and compact. They have a fixed handle with a support area and are ideal for use in confined areas. Suitable for cutting up to 60mm diameter copper and aluminium cables, and for multiple stranded cable. NOT suitable for steel wire or wire ropes. Specification Length: 320mmCutting Capacity: 60mm / 600mm

The Knipex 95 32 315 Cable Cutters cut through steel wire armoured cables with a diameter of up to 45mm, using one or two-handed operation. Not suitable for ACSR cable or wire ropes. It has a low weight, compact design that is great for using in confined areas. The innovative three-stage ratchet-drive ensures high leverage for easy cutting in one-handed and two-handed operation. The steel cutting edges are hardened and precisely ground, ensuring a smooth, neat cut without crushing. They have a fixed handle with a support area and are ideal for use in confined areas.

Knipex Cable Cutters with heavy-duty telescopic handles made of oval aluminium tubing. Extendable up to 770mm for maximum leverage on large cable diameters. Retractable down to 570mm for minimum space requirements during transport. The cutting head is made from special quality, high-grade tool steel, oil-hardened. Fitted with an adjustable bolted joint. Suitable forcable diameters up to 38mm, handles can be positioned at an angle to set the optimum handle width, which makes the shear also suitable for work in confined areas. They are comfortable to work with, thanks to the ratchet action and low weight. The cutting head can be replaced if needed. Specification: Cutting Capacity: 38mm / 280mmHandle Length Range: 570-770mm

These Knipex Ratchet Action Cable Shears have the following specification: Length: 280mmCapacity: 52mm / 380mmAluminium Sector Cable: up to 4 x 150mm

These Knipex Ratchet Action Cable Shears have the following specification: Length: 250mmCapacity: 32mm / 240mm

The Knipex 95 26 165 Cable Shears are fitted with a Return Spring.

These Knipex Cable Shears are fitted with an internal opening spring, protected and captive. Specification: Length: 165mmCutting Capacity: 15mm / 50mm

These Knipex VDE Cable Shears feature a twin cutting edge, initial and final cut (upper and lower blade) allows cables of up to 20mm dia. to be cut. Low effort required due to high transmission ratio and blade geometry.

1 x Knipex VDE Cable Shears 165mm

These Knipex Cable Shears are fitted with ergonomic multi-component grips for added grip and comfort. Specification: Length: 200mmCutting Capacity: 20mm / 70mm

These Knipex Cable Shears are fitted with ergonomically PVC coated styled handles for added grip and comfort. Specification: Length: 200mmCutting Capacity: 20mm / 70mm

1 x Knipex Cable Shears PVC Grip 165mm

1 x Knipex Electrician's Shears 155mm

The Knipex TwistCut is suitable for cutting empty or ready assembled corrugated pipe with a diameter of 13-32mm. The exact flush cut blades quickly and easily cut corrugated pipes to length without damage and leave no sharp edges. Blades are recessed to avoid injury. The slim ergonomically designed body is made of a robust polyamide compound plastic whilst the double-sided guide ensures a precise cut. There is also a practical wire stripper. Ideal for the construction, plumbing and electrical trades, for cross-sections: 0.2, 0.3, 0.8, 1.5, 2.5, and 4mm. Specification: Pipe Capacity: 13-32mmWire Capacity: 0.2-4.00mmOverall Length: 100mmWeight: 46g

These Knipex 88 06 Series Alligator VDE Water Pump Pliers are fitted with multi-component grips, VDE tested up to 10,000V and safe for work up to 1,000V. They conform to DIN EN / IEC 60900. Self-locking on pipes and nuts: no slipping on the workpiece and low handforce required. With a box-joint design for high stability. Made from chrome vanadium electric steel, forged, multi stage oil-hardened. Chrome plated finish. The gripping surfaces feature special hardened teeth, teeth hardness approx. 61 HRC: high wear resistance and stable gripping. These pliers offer good access to the workpiece due to slim size of head and joint area. Specification Capacity: Pipe: 50mm, Nut: 46mmLength: 250mm (10in)

Knipex 88 01 400 Alligator Water Pump Pliers PVC Grip Size: 400mm.Pipe Capacity: 90mm.Hex Capacity: 95mm.

Knipex 88 01 300 Alligator Water Pump Pliers PVC Grip Length: 300mm (12in).Pipe Capacity: 70mm.Hex Capacity: 46mm.

Knipex 88 01 250 Alligator Water Pump Pliers PVC Grip is supplied loose unpackaged. Length: 180mm (7in).Capacity: 36mm.

Knipex 88 01 250 Alligator Water Pump Pliers PVC Grip Length: 250mm (10in).Pipe Capacity: 50mm.Hex Capacity: 36mm.

Knipex 88 01 180 Alligator Water Pump Pliers PVC Grip Length 180mm (7in).Pipe Capacity: 42mm.Hex Capacity: 36mm.

These Knipex 8751250 extra slim Cobra Water Pump Pliers have automatic adjustment and they can be opened and adjusted directly at the workpiece with one hand. The handles incorporate a multi-purpose press button for fine fitting directly onto the workpiece. The extra long narrow jaws provide good access. The integrated spring of the automatic adjustment is shielded in the handles for user safety and the gripping surfaces have special hardened teeth which are hardened to approx. 61 HRC. These Knipex 8751250 pliers are low wearing but have a secure gripping action. The combination of a fine adjustment, which ensures optimum adjustment to differently sized workpieces, a user-friendly handle position and a secure catching of the hinge bolt ensures against unintentional shifting when in use. The box-joint design offers high stability and the double guide will hold securely on nuts or bolts. A secure grip is provided with the minimum of hand force. These Knipex water pump pliers have a user friendly guard to prevent the operator's fingers being pinched. The pliers are made from strong chrome vanadium electric steel that has been forged and then oil-hardened for added strength and durability. They have PVC dipped handles for user comfort and a positive grip. Specification: Length: 250mmCapacity: Pipe 32mm, Nut 42mmAdjustment positions: 19

Knipex concentrate their knowledge and expertise on pliers, wrenches and cutters. This is the only way to justify there claim they are the best supplier in terms of quality, innovation and efficiency. Knipex products satisfy the highest expectations in terms of performance, ergonomics and service life. There products are designed to meet the requirements of professional users, who must be able to rely on their tools in day-to-day work. With over a thousand separate styles and sizes. Knipex offer a complete range of pliers for almost every application in trade and industry. The breadth and depth of their range ensures that the best tool can always be found for every application. Particular attention is paid to ergonomic criteria in the production of their pliers and cutters, above all in the form of effort-reducing constructions and a handle design which is ideally suited to the moving hand and ensures minimum fatigue and safe work. The Knipex KPX8741250 multiple slip joint plier is a combination tool that offers the convenience of the comfortable push-button adjustment on the workpiece and the function of an adjustable spanner. The jaws provide a secure and tight grabbing of bolt heads with rounded edges, rusted nuts or heavily coated workpieces and have a self-locking range of 10-32 mm (11/16-inch - 1,1/4-inch) with 15 fine adjustment positions. The ergonomic handles are coated with a non-slip plastic coating for a comfortable grip particularly with big and tight nuts.Length 250mm (10 in)Capacity 32mm

The Knipex 87 26 Series VDE Cobra Water Pump Pliers are fitted with multi-component grips, VDE tested up to 10,000V and safe for work up to 1,000V. They conform to DIN EN / IEC 60900. They are adjusted by shifting one jaw directly on to the workpiece and can then be opened at the touch of a button off the workpiece. They have a fine adjustment for optimum adaptation to different sizes of workpieces and a comfortable handle width. The slim size head and joint area allows for good access to the workpiece and they are self-locking on pipes and nuts: no slipping on the workpiece and low hand force required. The gripping surfaces have special hardened teeth, teeth hardness approx. 61 HRC which makes for low wear and stable gripping. The box-joint design gives high stability because of double guide and the guard prevents operators' fingers being pinched. Specification Capacity: Pipe: 50mm, Nut: 46mm

Knipex 87 22 250 Cobra Quickset Water Pump Pliers Multi Component Grips

Knipex 87 21 300 Cobra Quickset Water Pump Pliers PVC Grips

Knipex 87 21 250 Cobra Quickset Water Pump Pliers PVC Grips