Monument 2644Q Plastic Pipe Cutter. Maximum Pipe Size: 28mm.

Monument Pipe Cutter is a high quality tool for use by professional and DIY Plumbing Installers, heating engineers, and maintenance staff. It assures a square even cut and all parts liable to wear are heat-treated. For sizes: 4mm up to 22mm (copper tube).

1 x Monument 262S White Tallow 495g Tub.

This Monument 2611S Mini Bender is for up to 180 bends on 6, 8 and 10mm copper pipe (outside diameter).

Spare pipe bender Guide for Monument 2603T 22mm pipe bender. Will also fit Record 218M and Hilmor GLM benders. Specifications:Size: 22mm.

Spare Pipe Bender Guide for Monument 2601N 15mm pipe bender. Will also fit Record 218M and Hilmor GLM benders. Specifications: Size: 15mm.

The Monument Copper Pipe Bender, 15-22mm, is designed to professionally bend BSEN1057 15mm and 22mm copper pipe and 15mm stainless steel tube. The aluminium formers are marked with bending angles of 30, 45-and 90-degree offsets allowing for accurate bending. The Monument Pipe Bender is supplied with a replaceable 15mm (MON2601) and 22mm (MON2603) aluminium bending guides.The Monument Pipe Bender can also be used with the MON2626 2626M Bending Arm Extension allowing for easier bending of 22mm pipe. Replacement guides, formers and hook stops are available separately.

Monument 259I Gas Test Gauge has the following specification: Size: 900mm (36in).Capacity: 90 Millibar.

The Monument 2580U Vent Sizing Gauge is used to measure the size of the slots in an air vent to calculate the area of ventilation provided by a vent where this info is not readily available. The gauge is stepped in increments of 1mm and will measure vent slots from 5mm up to 10mm. Made from stainless steel.

Monument 258F Gas Test Gauge. Size: 600mm (24 in).Capacity: 60 Millibar.

Monument 257C Gas Test Gauge. Size: 300mm (12 in).Capacity: 30 Millibar.

The Monument Mains Water Pressure Testing Gauge with 3/4in BSP thread for fitting to taps. Maximum Pressure: 11 bar

The Monument Drain Down Hose is designed to lay flat when draining down a central heating system. Unlike standard hose pipe, when uncoiled the hose lays flat, allowing water to flow with gravity. Complete with a hose clip to affix to the drain off cock. The silicone rubber hose can be coiled neatly with hook loop fasteners for storing/transporting. Specification: Length: 15mInternal diameter: 12mmOutside diameter: 19mm

The Monument 2363L OMAT Soldering Mat has the following specifications: Size: 150mm (6in)Pipe Capacity: 15-22mm

The Monument 2361F OMAT Soldering Mat has the following specifications: Size: 250mm (10in)Pipe Capacity: 15-22mm

The Monument 2355M OMAT Soldering Mat has the following specifications: Size: 305mm (12in)Pipe Capacity: 15-22mm

Monument 2351A Soldering Brazing Pad resists temperatures up to 600 Celsius, and does not present any of the hazards associated with asbestos material. Made from HDW graphite material Size: 250mm (10in).

Monument 2350X Soldering Brazing Pad resists temperatures up to 600 celsius, and does not present any of the hazards associated with asbestos material. Made from woven glass fabric (Professional quality). Size: 300mm (12in).

Monument Glass Fibre Plumbers Mat is an asbestos free, heavy-duty and professional quality mat that provides protection in most soldering and brazing work. The mat resists temperatures up to 600 C, and does not present any of the hazards associated with asbestos materials. Made from glass fibre fabric. Size: 300 x 250mm (12 x 10in)

The Monument MON22R suits 22PC Automatic Pipe Cutter and 1722 pipe cutter. Ideal for use when space is limited.

Monument Automatic Copper Pipe Cutter. Size: 22mm.

Monument Automatic Copper Pipe Cutter, 22 in a display jar. Size: 15 mm. Ratchet handle available (Code:- MON15R.)

The Monument 2166M TRV Tail Driver Fitting Socket has been designed to enable fast removal and installation of radiator valve tails and will fit most makes and sizes. The socket can be used with a either a cordless drill chuck or ratchet with 10mm hex socket.

The Monument Professional Power Plunger comes with 3 adaptors which should fit most shower, bath, basin, and bidet wastes. When pumping the MON2161X unit in situ, it will build up pressure which is then activated via the trigger to blast away the blockage. When the trigger is pulled quickly the compressed air is discharged, at once, causing a shock wave through the water to dislodge the blockage within the waste, even if it is past the trap, down the pipework and around several bends.

The Monument 2117Q Pro Deburring Tool is ideal for deburring inside copper pipe. Its swivelling blade rotates freely to enable allsorts of deburring operations to be carried out on the inside of pipes, on sheet materials, inside holes etc. The blade is replaceable. The deburrer is suitable for use on steel, copper, brass, plastics, wood and castings.

This Monument 2116N Burrfect Square Deburrer cleans and deburrs 4 different sizes of plastic waste pipe, it is a high quality metal square with each side de-burring a different size of plastic pipe.This deburrer tool will deburr the following sizes: 19mm (3/4in), 32mm (1.1/4in), 38mm (1.1/2in) and 50mm (2in).The 2116N includes a handy hanging hole, and is made in Britain.

The Monument Heavy-Duty Compression Fitting Spanner is double ended it has 24mm and 32mm ends for 15 and 22mm compression fitting nuts.The 2069R spanner conforms to DIN 895 standards. Specifications: Size: 15 x 32mm.

This Monument Radiator Valve Spanner is used to facilitate fitting and removal of standard and thermostatic radiator valves.The 2065F is made in Britain.

These Monument Radiator Bleed Keys are used for releasing the excess air trapped in a radiator.They each have a clock key design for convenient attachment to a keyring. Specification: Pack Quantity: 2.

This Monument Three-Legged Radiator Valve Key is used for 1/2in, 3/4in and 1in radiator valve's. It has 7, 8 and 9mm square profiles.The key is made from brass pressing.

The Monument Radiator Spanner Air Release Key, 2054X, made from steel, a zinc plated valve spanner and an air release key, with a slightly offset handle. Specification: Size: 12mm (Double Ended).

This Monument Steel Radiator Spanner is used on 3/8 in and 10 mm square section radiator vent plugs and bleed screws.It has a Zinc plated finish with a slightly offset handle.

This Monument Universal Radiator Valve Key has tapered ends and are therefore self-restricting. The three profiles make the tool universal, catering for 3/8 in and 10 mm square section radiator vent plugs and bleed screws.Bayonet or internal lug type radiator valves allow for variations in size, shape, and position. The 12 mm to 14 mm internal hexagon valves are tapered allowing for variations in size.

Monument Radiator Spanners Twin Pack with 1 x 10mm and 1 x 12mm square section radiator spanners. Suitable for vent plugs and bleed screws. They are made from zinc plated steel with a slightly offset handle for ease of use.

The Monument 2050L Gas Meter Radiator Bleed Key is used for releasing air which can appear in a radiator, and for opening gas meter cupboards.Made in Britain from engineering plastic.

This Monument Radiator Stepped Wrench Ratchet handle is suitable for use on most radiator valves, nipples, plugs, tank connectors etc. It has the following step sizes 10, 12, 12.7, 17 22mm.

Twin Pack of Compression Fitting Spanners 15/22mm.

The Monument; 2040G Pump Nut Spanner is suitable for use on most nuts found on domestic central heating pumps. It has a drop forged steel construction for durability. Size: 52mm A/F (2in).

Monument Compression Nut Fitting Spanner is a one piece all steel construction compression nut spanner, that is single ended and made from drop forged steel for added strength and durability. Will suit most 28mm compression nuts and has an overall length of 290mm.

The Monument 2035Q; Olive Puller is ideal for removing olives from copper piping without damaging the attached pipe. Suitable for 15mm copper pipe. This puller simply engages with 14tpi thread of the compression fitting to remove the olive from the tube. With a 1/2in square drive for attachment to a ratchet. Made in Britain.

Single pack.

The Monument 1851O Vari Pitch One Piece Holesaw has the following specifications:

The Monument 1850L; Vari Pitch One Piece Holesaw has the following specifications:

The Monument 1848E Vari Pitch One Piece Holesaw has the following specifications:

This Monument Tee Piece for U Gauges connects three pieces of rubber hose together for convenient connection to U Gauge, bellows and nipple cap.

Monument MON1810 Autocut Cooper Pipe Cutter . Size: 10mm.

The Monument MON1808 1808O Autocut Copper Pipe Cutter comes in the following: Size: 8mm

The Monument MON1806 1806L Autocut Copper Pipe Cutter comes in the following: Size: 6mm.

The Monument MON180 180S Nipple Cap are for attachment to drain test plug outlets to enable connection of rubber hose to the U Gauge. It is made from plastic with a washer. Specification: Size: 1/2in BSP.

Monument Lead Ladle with a handle welded to a pressed steel bowl with a zinc plated finish. Suitable for pouring molten metals and compound. Bowl diameter: 100mm (4 in).

Using Monument Hand Bellows, air may be carefully pumped into the pipe. Fitted with a positive, hand operated non-return valve. Designed for use with Monument Air testing U Gauge kit.

The Monument 175C U-Gauge (also known as a Manometer) should be used to test for leaks after installation or repair of any drain or pipeline system. Made from unbreakable parts, it will test up to 100mm (4in) water gauge pressure irrespective of pipe diameter. The hinged lid of the gauge folds back so that it forms a base behind the gauge for added stability.

Monument Air Testing U-Gauge Kit containing all the items (except testing plugs) needed to carry out an air test to 100mm (4in) water gauge pressure on any size of drain or pipe. The kit is housed in a display box with full instructions. Contains: 1 x U-Gauge1 x Hand Bellows Pump1 x 1/2in BSP Nipple Cap1 x 1in BSP Nipple Cap1 x Y-Piece3 x 600mm lengths of Rubber Hose

Easyslice kit of 2 pipe cutters and handles Pipe size: 15 22mm

Test Nipples screw into gas meters to enable connection to a gas test gauge. The hexagon screw shuts off supply to the gauge.1/8in. BSP thread.

The Monument 1730X Orange Hose for Gas Test Gauges. Rubber Hose ID: 5.5mm food quality, Length: 2m. Colour: Orange

Monument 173 has been especially designed for removing stiff backnuts from awkward placed taps and to make tap installation a more rapid process, this tool is for 1/2-inch. BSP and 3/4-inch. BSP taps. The Monument 170 tool stays in position on the tap tail so can be used with one hand and uses mechanical advantage of the thread of the tap tail to remove stiff nuts. Ideal for 1/2-inch and 3/4-inch BSP 25 mm 27 mm nuts 29 mm ribbed 32 mm nuts. The MON173 is complete with 3/8-inch cordless drill adaptor, 1/2-inch square drive, extension tube and full user instructions. For removing stiff backnuts and rapid tap installation for 1/2-inCH. BSP and 3/4-inch. BSP Taps.Tool stays in position on the tap tail. Uses mechanical advantage of the thread of the tap tail to remove stiff nuts. Monument Stiffnuts Professional Boxed Kit. 1/2-inch. and 3/4-inch. BSP 25 mm 27 mm nuts 29 mm ribbed 32 mm nuts. Complete with 3/8-inch. Cordless drill adaptor, 1/2-inch. Square Drive; Extension tube and full instructions.

This Monument spare rubber hose is for use with U gauges. They have a coil length of 2m and an internal diameter of 7/32in (5.5mm). Specifications: Colour: Black.Length: 2m (78in) (coil).

Monument MON1728 Autocut Copper Pipe Cutter. Size: 28mm.

The Monument MON1727 1727N Autocut Pipe Cutter comes in the following:Size: 27.4mm.

The Monument Autocut Twin Pack contains the following: 1715C: Size: 15mm.1722Y: Size: 22mm Not for use on stainless steel. Spare wheel to fit is available MON269.

Monument 1712t Autocut Copper Pipe Cutter. Size: 12mm.

The Monument 170 Stiffnuts, 27 x 32mm, Kit has been especially designed for removing stiff backnuts from awkwardly placed taps, and to make tap installation a more rapid process.This tool is for 1/2-inch. BSP and 3/4-inch. BSP taps. The 170 tool stays in position on the tap tail so can be used with one hand and uses mechanical advantage of the thread of the tap tail to remove stiff nuts.Ideal for 24mm A/F, 25mm A/F, 26mm A/F and ribbed, 27mm A/F, 29mm A/F ribbed, A/F 32mm. It comes complete with 3/8-inch cordless drill adaptor and a full user instruction manual. Specifications: Capacity: 1/2in 3/4in.Pack Quantity: 6 Pieces.

The Monument MON15R suit 15PC Automatic Pipe Cutter and 1715 pipe cutters.

Monument Automatic Copper Pipe Cutter. Size: 15 mm. Ratchet handle available (Code:- MON15R.)

The Monument 1515U Water Flow Weir Gauge is designed to measure water flow rates in order to determine if suitable flow is available in a building prior to the plumbing installation of washing machines, boilers, showers etc. This type of water flow gauge is also used for diagnosing if a combi boiler or water heater may need de-scaling. The water flow gauge is made from durable plastic with a stainless steel mesh strainer to avoid turbulence. It features a dual scale to measure flow rates of 2 to 25 litres and 1 to 5 gallons per minute.

Monument Pipe Dry Testing Kit is ideal for dry testing pipework during and after installation. The 1512 has an easy to read triple scale bar in psi and kPa scales and is suitable for water, air, gas and petroleum oil pipes up to 4 bar, and for testing combi systems. Can be left on test, while flooring is laid to reveal any nail damage. It can also test hot and cold supplies separately to ensure pipes are not crossed. The Monument 1512 is fitted with a Schrader Valve and 15 mm push-fit fitting for quick and easy assembly and has a rubber boot for added protection.

The Monument 1470F Smoke Emitter Pellets give off a dense white low-toxic smoke when ignited. They have a burn time of 60 seconds and have an approximate volume of 15m³.They are used for testing flues, chimneys, fans etc and come supplied in a pack of 10. Specification: Smoke Colour: White.Pack Quantity: 10.

This Monument 1469B Mini Snake Barbed Drain Unclogger quickly unclogs sinks, showers, bath drains, bathtubs, and laundry tubs.There is no need to remove the rose. Specifications: Size: 10mm.Length: 75cm.

This Monument 1461 Micro Yellow Plunger is ideal for clearing small hand basins. This 100mm diameter plunger has a compact design for ease of storage. It is for use on bathroom and kitchen sinks. Specifications:Colour: Yellow.Cup Size: 100mm (4in).

Monument one-piece Plunger, in black, for clearing sinks, basins, and bath wastes is both handy and popular. Exclusively patented bellows design allows more cubic centimetre displacement than traditional force cups. Specifications: Size: 100mm (4in).Length: 325mm (13in).

This plunger is ideal for bath and sink waste pipes. Size: 125mm (5 in).

1 x Monument 1458T Large Force Cup Plunger 120mm (4.3/4in)

1 x Monument 1457Q Medium Force Cup Plunger 100mm (4in)

1 x Monument 1456N Small Force Cup Plunger 75mm (3in)

This Monument Suction Plunger is ideal for clearing WC pan wastes and gullies. It is made from soft, flexible rubber and has a wooden T-handle. Rubber Diameter: 140mm (5.1/2in)Overall Length: 445mm (17.1/2in)

The Monument Hydro-jet Pump safely provides the explosive power of a water jet to unblock sinks, baths, showers, toilets, and drains. First you fill the unit with water then hold the unit over the waste and pump down (or hit) the handle to create a powerful water jet to help clear any blockage. To clean the MON1452 simply just flush with clean water. Comes with 3 adaptors for sinks, drains and toilets. Size: 35cm x 7cm x 7cm.

The Monument MON1445 1445F spare hose for connecting testing equipment comes in the following: Length: 1m.Internal Diameter: 10mm.

This Monument 138R Copper Pipe Jointer has the following specification: Pipe Diameters: 15mm and 22mmPipe Thickness: 0.7mm and 0.9mm

Monument 1379 Testing Plug. Size: 150mm (6 in).Capable of sealing against pressures of up to 1.62 bar / 24 psi.

Monument 1378Z Drain Testing Plug. Size: 100 mm (4 in).Capable of sealing against pressures of up to 1.97 bar / 29 psi.

The Monument MON1377 1377W Drain Testing Plug comes with the following specifications:Size: 75mm (3 inch).Capable of sealing against pressures of up to 2.24 bar / 33 psi.

Diameter range: 48-62mm. Maximum allowable back pressure: 37psi (2.50bar).1/2 in BSP outlet.

Monument Drain Test Plug is suitable for blocking off small pipes such as copper for dry testing prior to commissioning. It cannot be used for air testing purposes by itself. Diameter range: 37-45mm. Maximum allowable back pressure: 60psi (4bar).

This Monument set of 6 Test Plugs contains the following small bore test plugs: 2 x 1370B 15mm Test Plugs.2 x 1371E 22mm Test Plugs.2 x 1372H 28mm Test Plugs. The plugs are used for blocking off small pipes such as copper pipes for dry testing prior to commissioning, however they cannot be used for air testing purposes by themselves.

The Monument MON1368 1368U 2 Piece Test Plug Set is used for blocking off small pipes such as copper pipes for dry testing prior to commissioning. They cannot be used for air testing purposes by themselves. 2 Plugs supplied: 1 x 1370B 15mm Test Plug. 1 x 1371E 22mm Test Plug.

Monument 134F Socket Forming Tool. Size: 28mm.

Monument 133C Socket Forming Tool. Size: 22mm.

Monument 131W Socket Forming Tool. Size: 15mm.

This Monument pump is for use on Schrader valves, and they are used for inflating flexible plugs and universal flexible plugs which are fitted with a Schrader valve. Note: inflate flexible plugs slowly, stop inflating when seal is achieved.

The Monument Air Bag Stopper is a durable, quality flexible air bag stopper for the plugging of drains and pipes. This bag is made with a durable nylon outer casing that gives the air bag a better seal and grip on the tube or pipe being repaired or replaced. It has a long feed hose that is fitted with a Schrader valve to quickly release the pressure. Inflate with a MON1308 pump.

This Monument AC4P Autocut Plastic Pipe Cutter is suitable for 28mm plastic plumbing pipe.

Monument 1279 Black replacement hose to fit gas test gauges, are 1m in length, and have an internal diameter of 7/32 in (5.5mm). Note: Do not use this hose for LPG (Liquified Petroleum Gas).

This Monument 1277s is a replacement hose to fit gas test gauges. It has an internal diameter of 7/32 in (5.5mm). They are black nitrile for standard and are 1m in length (Coil). NOTE: Do not use this hose for LPG (low pressure gas).

This Monument AC4P Autocut Plastic Pipe Cutter is suitable for 22mm plastic plumbing pipe.

This Monument AC4P Autocut Plastic Waste Pipe Cutter is suitable for 2in Push Fit and Solvent Weld waste pipe. Whilst nominally called 2in pipe, the Push Fit and Solvent Weld pipe actual sizes vary from 50mm I.D. inner diameter to 56mm O.D. outer diameter.

This Monument AC4P Autocut Plastic Pipe Cutter is suitable for 15mm plastic plumbing pipe.

This Monument AC4P Autocut Plastic Waste Pipe Cutter is suitable for 1.1/4in Push Fit and Solvent Weld waste pipe. Whilst nominally called 1.1/4in pipe, the Push Fit and Solvent Weld pipe actual sizes vary from 30mm I.D. inner diameter to 36mm O.D. outer diameter.

This Monument AC4P Autocut Plastic Waste Pipe Cutter is suitable for 1.1/2in Push Fit and Solvent Weld waste pipe. Whilst nominally called 1.1/2in pipe, the Push Fit and Solvent Weld pipe actual sizes vary from 37mm I.D. inner diameter to 43mm O.D. outer diameter.

This Monument AC4P Autocut Plastic Pipe Cutter is suitable for 10mm plastic plumbing pipe.